Choosing a home battery is less about matching your household’s total daily electricity use and more about deciding which loads must operate, for how long, and whether solar can recharge the system. This guide provides a repeatable battery-sizing worksheet, appliance runtime estimates, and practical rules for comparing essential-load and whole-home backup.
Overview
Home battery sizing has two separate questions: how much power the battery can deliver at one moment, and how much energy it can store over time. A system may have enough stored energy to run a refrigerator overnight but still be unable to start a large air conditioner or well pump if its inverter cannot handle the startup surge.
When comparing batteries, look beyond the headline capacity. Check the usable capacity, continuous power rating, peak or surge rating, round-trip efficiency, operating temperature range, backup configuration, warranty terms, and whether the quoted system includes the required inverter and transfer equipment. Usable capacity is the portion available for household loads after the manufacturer’s operating reserve and battery controls are considered.
There are three common backup goals:
- Short essential-load backup: refrigeration, lights, internet equipment, medical devices, and selected outlets for several hours.
- Overnight or extended essential-load backup: the same priority circuits, possibly including a sump pump, well pump, or limited heating and cooling.
- Whole-home backup: most or all circuits, including high-demand equipment. This generally requires more inverter power, more storage, load controls, or all three.
A larger battery is not automatically the best answer. Improving insulation, sealing air leaks, pre-cooling or pre-heating the home, and separating flexible loads can extend outage runtime more affordably than adding storage alone. See the home energy audit priority checklist and insulation and air-sealing comparison before finalizing a system.
How to estimate
Start with a load list rather than a battery brand. For each appliance, record its running watts, expected hours of use, and whether it has a motor or heating element. Then use this basic calculation:
Daily energy needed = watts × hours of operation ÷ 1,000
To estimate required battery capacity, add the daily energy for all priority loads, multiply by the number of outage days you want to cover, and divide by an allowance for conversion losses and operating reserve. Because real-world performance varies, treat the result as a planning estimate rather than a guarantee.
For example:
- List the loads that must remain on.
- Estimate each load’s watts and hours per day.
- Add the results in kilowatt-hours (kWh).
- Multiply by the desired backup duration.
- Add margin for cold weather, battery aging, uncertainty, and unexpected use.
- Confirm that the inverter can support the largest simultaneous and startup loads.
Do not size solely from a monthly utility bill. A bill shows total energy over time, while backup design depends on the specific circuits operating during an outage. A smart energy monitor, appliance label, plug-in meter, or electrician’s load assessment can produce better inputs. The smart thermostat and energy monitor comparison may help identify which household loads are flexible or unusually large.
Inputs and assumptions
Estimated appliance loads
The following ranges are broad planning estimates. Actual consumption depends on model, duty cycle, weather, controls, and installation. Use manufacturer data or measured readings when available.
| Load | Typical planning approach | Important sizing issue |
|---|---|---|
| Refrigerator | Use average running consumption, not continuous full-power operation | Compressor startup surge |
| LED lights | Count the bulbs used during an outage | Usually modest energy demand |
| Internet equipment | Router and modem operating for the desired hours | Small load, but often a high priority |
| Medical equipment | Use the device label or measured draw and required duty cycle | Reliability and professional guidance are essential |
| Sump pump or well pump | Estimate total minutes or cycles per day | Starting watts can be several times running watts |
| Heating or cooling system | Estimate actual runtime under outage conditions | Compressor, fan, electric resistance heat, and controls vary widely |
| Electric water heater | Count only if hot water is a priority | Heating elements are high-demand loads |
| EV charging | Usually schedule, reduce, or exclude during an outage | Can consume a large share of stored energy |
Power rating versus energy capacity
Continuous power, measured in watts or kilowatts, determines how much load the inverter can support at once. Peak or surge power determines whether the system can start motors and compressors. Usable capacity, measured in kWh, determines how long the battery can provide energy.
Make a list of loads that may run simultaneously. A refrigerator, sump pump, microwave, and HVAC compressor can create a different requirement from the sum of their average energy use. Ask the installer to show the proposed system’s continuous and surge limits, not just its storage capacity.
Solar recharge and load shedding
Solar can extend an outage, but its contribution depends on weather, roof orientation, shading, season, battery state of charge, and whether the solar array is designed to operate when the grid is down. Confirm that the proposed solar-plus-storage system can recharge during an outage; not every configuration provides the same functionality.
Load shedding makes a smaller battery more practical. Examples include disabling an EV charger, electric water heater, clothes dryer, pool equipment, or resistance heating while backup power is active. A managed HVAC system may also reduce runtime by widening the temperature range. Ask whether these controls are automatic, manual, or dependent on a compatible panel or energy-management system.
Worked examples
Example 1: Essential loads for one evening
Suppose a household prioritizes a refrigerator, internet equipment, several LED lights, and a medical device for eight hours. The refrigerator cycles rather than running continuously, while the lights and internet equipment run for only part of the period. The household should total the measured or estimated energy for those loads, then compare it with the battery’s usable capacity after allowing for conversion losses and reserve capacity.
The inverter must also support the refrigerator’s compressor startup and the medical device’s required operating conditions. If the system passes the energy calculation but fails the surge requirement, the battery may not start the load reliably.
Example 2: Overnight backup with a sump pump
A sump pump may run only intermittently, so its daily energy use can be moderate even though its starting demand is significant. Add its estimated cycles to the refrigerator, communications, lights, and any heating or cooling controls. Because rainfall, groundwater, and weather are uncertain, include a reserve and verify the pump’s startup rating with the installer.
If the battery cannot support the pump’s surge, options may include a different inverter, a compatible soft-start solution, a separate backup arrangement, or a revised critical-load panel. Do not assume that adding more kWh fixes an inverter-power problem.
Example 3: Multi-day outage
For a two- or three-day outage, calculate a daily essential-load budget and multiply it by the target duration. Then identify which loads can be shifted, shortened, or eliminated. A household may preserve refrigeration, communications, lights, and medical equipment while excluding EV charging and electric water heating. Solar recharge can change the result substantially, but plan for poor production rather than assuming every day will be sunny.
Whole-home backup requires a separate assessment. Large HVAC systems, electric resistance heat, cooking equipment, water heating, and EV charging can dominate both peak power and stored energy. Compare a whole-home design with an essential-load panel and automatic load management rather than comparing battery kWh alone. For panel capacity and EV-related constraints, see the EV charger panel upgrade and load-management guide.
When to recalculate
Revisit your battery sizing worksheet at least before each major outage season and whenever the underlying inputs change. Recalculate after adding or replacing a heat pump, air conditioner, electric water heater, well pump, sump pump, medical device, or EV charger. Also review it after home renovations, insulation work, solar expansion, a battery replacement, or a change from essential-load to whole-home backup.
Actual outage performance is valuable evidence. Record the starting state of charge, weather, appliances used, solar production, and time until the battery reached its reserve. If runtime was shorter than expected, check whether the cause was a larger-than-assumed load, inverter limits, cold-weather performance, battery reserve settings, or a communications and control issue.
Before requesting quotes, prepare your load worksheet and ask each installer to identify usable capacity, continuous power, peak power, expected recharge behavior, cold-weather limitations, installation requirements, and the circuits included in backup. Compare those details line by line using the solar quote comparison checklist. Battery specifications, installation costs, warranty language, and available incentives can change, so verify current details directly in each proposal. For maintenance and capacity-loss planning, use the home battery maintenance and warranty guide.
The practical goal is not the largest battery. It is a system whose usable energy, inverter power, controls, and recharge plan match the loads you genuinely need during the outage you are preparing for.